ridge vent – Roof Ventilation Are Of Many Types Learn About It
Author: admin // Category: General
Roof Ventilation Are Of Many Types Learn About It
When the roof is the most important part of the house. It can prevent rain, snow, of course, Mother Nature dishes. Without them, we have a cold – literally. Build or buy an apartment, it is important to ensure good conditions for the roof. The roof of the most important there is adequate ventilation.
Problems can occur
Poor ventilation provide moisture, and eventually leads to the roof structure. We must also ensure that adequate ventilation of the roof to increase roof life and contribute to the safety of all at home. In addition, temperature and humidity to increase the cooling costs, energy costs. Moisture can cause ice dams, and other issues, such as rot fungi.
Different types of roof ventilation and roof vents
There are many roof ventilators that are available in a variety of dormers and turbines. The most important thing is to keep the practical options that should be taken to ventilation. A good ventilation system is composed of two types of valves:
Intake.
These vents allow fresh air into the house.
Vent.
Allow air to leave the house.
Bleeding from the system, both the intake and exhaust valves installed. Installed correctly through the house, fresh air ventilation system, while others are sent to the outdoor air.
Call the Professional
To live according to their own professional area of the law a contractor can give you the information necessary to open a different roof, but also easier to go home. For certain types of roof vents better than others on the roof of the structure and style can be. The cathedral’s roof, for example, needs a ridge vent, in order to provide adequate ventilation, and some of the houses and to improve the turbine vent, this is free air circulation.
Different types of roof ventilation and roof longevity
When the growth of the roof of the surrounding buildings, the ventilation of life. This can save a tremendous future, not to buy a new roof. If your house is well ventilated, humid air does not go anywhere. Since the sit in, it will damage the time. Although it does not appear to the emergence of the first occurrence of the damage, and to increase without proper ventilation, Engineering, the
1000
roof, the deterioration of family structure.
By: windwb
Article Directory: http://www.articledashboard.com
In today’s world where pollution is on the rise, we make sure that you can breathe pure fresh air. Our efforts are based around roof ventilation, industrial roof ventilation. We are Suppliers & Dealers of Wind Ventilators,Hybrid Ventilators,Turbine Ventilators. We are known as Hurricane Turbine Ventilator Dealers and Suppliers and are located in Pune Maharashtra India
Shingling or roofing a house is a major undertaking for a homeowner and extreme caution is required. This said, a Do-It-Yourselfer homeowner can shingle or roof their own home with a little knowledge and the right tools.
Required Tools
In order to roof a house properly and safely the following tools are needed: Ladders, Roof Jacks, Hammer, Carpenters Knife, Chalk Line, and preferably a compressor or nail gun.
Estimating Materials
Typically the roof is measured in squares, where a “square” represents 100 square feet. There are eighty shingles in one square. However, when you go to your local home improvement store shingles are usually sold in bundles. Usually three bundles equal one square, however this can vary slightly pending the shingle style.
Measure the area of your roof (length x width) and divide by 100 to get the number of squares required. Then multiply this number by three to get the number of bundles of shingles required for the job. Add an additional 10-15% for spare, leaning toward the 15% if your roof has hips and valleys.
Drip edge, ice and water shield, asphalt paper, flashing, roofing nails, and hip and ridge vents will also be required. The Drip edge comes in various lengths. Measure the outside perimeter of the roof to calculate the drip edge required. The ice and water shield, asphalt paper and flashing come in roles. Use your roof square area calculation for determining your asphalt paper requirements. Typically only one or two courses of ice and water shield is required along the bottom/eave of the roof and in the valleys. Calculate 2 times the length of the roof and valleys to estimate the amount of ice and water shield required.
Typically each shingle will require 4-6 roofing nails and flashing usually comes in 16″ wide roles or 6×6 or 8×8 square inch steps. Step flashing is typically used around chimneys, dormers and side wall junctions. Hip and Ridge vent will vary with local building codes, however a rough estimate would be to measure the length of your roof’s hip and ridges and take 75% of this figure for calculating the amount of vent required.
You should now be able to fairly accurately calculate the cost of material for roofing your home.
Installing the Drip Edge
Nail the Drip edge around the entire outside perimeter of the roof.
Apply the Ice and Water Shield Membrane and the Asphalt Paper
Apply the ice and water shield material such that it is flush with the drip edge. If the climate in your area has harsh winters and/or significant annual rainfall, add a second course of ice and water shield for added protection. You should also add the ice and water shield membrane in the valleys.
Next apply the asphalt paper to the entire roof, starting from the bottom and working towards the ridge. Make sure each course of asphalt paper overlaps the lower row by several inches (effectively shingling with the asphalt paper).
Install metal flashing
Install metal flashing in all of the valleys. Step flashing around chimneys and dormers will be added as the shingles are installed.
Installing the Shingles
Start the shingling at the bottom of the roof (or at the eaves). Lay a starter course such that the bottom edge of the shingle lines up flush with the drip edge. The starter strip is a “tabless” shingle that you make from the regular shingles using your carpenter’s knife.
Lay your next course of full shingles over the first course, staggering the starter joints from the first course to prevent water penetration.
Note: Sometimes you may want to start with a full or a partial shingle at one end. In either case, you want to try to avoid small shingle pieces at the far end of the roof. To prevent this, divide the length of the roof by the length of a full shingle and assess how much of a shingle length you want to start with. Ideally you do not want to have pieces smaller than 12″.
Use a Chalk Line
To ensure your shingle courses run straight use a chalk line. Measure the finished reveal on your shingles. Usually this is about 5 inches. Then make marks every 5 inches on the gable ends of the roof. Snap a chalk line between the gable ends at each pair of marks all the way up the roof. This will ensure that you shingles run true and straight as you progress up the roof with the courses.
Vertical lines should also be snapped every 3 to 6 feet to ensure your tabs maintain alignment.
Use of Roof Jacks
After 3 or 4 courses of shingles have been installed using ladders, roof jacks may be necessary to access the upper courses. Roof jacks are steel brackets that hold planks in position for you to stand on. The roof jacks should be securely nailed through the decking and into rafters to ensure that they will support your weight.
Shingling Valleys, Chimneys, Skylights and Dormers, and Step Flashing
Shingling the valleys and installing flashing requires extra care. The shingles, typically coming from two intersecting courses when entering a valley, need to overlap each other such that no water penetration occurs.
Skylights, chimneys and dormers must be step flashed (step flashing is interleaved with each course of shingles) to ensure water is kept from penetrating the roof.
Adding the Ridge Vent and Caps
To complete the roofing project, ridge vents need to be installed. These are nailed to the top of the ridge and then capped.
The ridge cap prevents water from entering the home via the ridge vent, while still allowing the house to breath. The ridge cap is constructed out of individual shingle tabs that have their unfinished corners cut off at 45 degree angles. Each modified shingle tab, is nailed such that it overlaps the previous piece as you work your way down the length of the ridge vent.
For more help on Shingling Your Home’s Roof, see HomeAdditionPlus.com’s Asphalt Shingle Roofing Bid Sheet at http://www.homeadditionplus.com/Bid-Sheet-Ebook-info/Asphalt-Shingle-Roofing-Bid-Sheet.htm. The Asphalt Shingle Roofing Bid Sheet will help to ensure that your roof won’t end up with a blue tarp over it and a dumpster sitting in your yard for weeks as you wait for the roofing contractor to come back and finish roofing your home.
1f48
Over the past 20+ years Mr. Donovan has been involved with building homes and additions to homes. His projects have included: building a vacation home, building additions and garages on to existing homes, and finishing unfinished homes. For more Home Improvement information visit: http://www.homeadditionplus.com and http://www.homeaddition.blogspot.com
Article Source:
http://EzineArticles.com/?expert=Mark_Donovan
Mail this post
Tags: ridge vent